#arpnetworks 2016-12-30,Fri

↑back Search ←Prev date Next date→ Show only urls(Click on time to select a line by its url)

WhoWhatWhen
***Lucifer333 has quit IRC (Quit: Leaving) [01:41]
........................................................................................... (idle for 7h33mn)
ziyourenxiang has quit IRC (Quit: Leaving) [09:14]
............. (idle for 1h2mn)
Lucifer333 has joined #arpnetworks [10:16]
....... (idle for 32mn)
pjs_ has quit IRC (Quit: leaving)
pjs has joined #arpnetworks
[10:48]
.............................................. (idle for 3h46mn)
staticsafenathani: you around?
trying to figure out how to put this Bell HH3000 ONT into passthrough mode
[14:34]
nathaniyup Im here
did you get your b1 number and password?
[14:37]
staticsafenathani: yeah I have it right here
Do I set the WAN mode to 'WAN Ethernet'?
[14:38]
nathaniwhat device do you want the public IP to land on?
dont need to change WAN mode
[14:41]
staticsafenathani: my Mikrotik router [14:41]
nathanihook up a port from one of the LAN connections over to WAN Port or Ether 1 on Mikrotik [14:42]
staticsafeyeah its connected that way now [14:42]
nathaniopen the gui / Mikrotik admin
get to interfaces
click the +
add a new pppoe client interface
Dial Out tab > put in the b1# and password
back to General Tab > select the interface hooked up to the Bell Modem / Router
you will need to configure NAT for the pppoe-out1 interface and your LAN / Bridge
[14:43]
staticsafenathani: just to be clear, am I supposed to have the ethernet cable in the red port marked as WAN or the yellow ports marked as LAN? [14:45]
nathanion the Bell device, LAN
and you dial out from behind that port even though it is giving you a private IP if you DHCP and have Internet connectivity
[14:46]
staticsafeoh I see what you mean [14:47]
nathaniyou will be using 2 public IPs essentially [14:47]
staticsafeyeah [14:47]
nathanione for the BELL / NAT
and Wifi will be using that one as well
other for your Miktrotik
what model mikrotik?
mine maxed out at about 240mbits/sec so I can't use it in my network
[14:47]
staticsafeCRS125-24G-1S-1RM [14:48]
nathaninice
dslreports.com had somone terminate the fiber directly onto CRS - if you are feeling adventurous and specifically since you have only Internet and no Phone or TV
[14:48]
staticsafenathani: problem is I can't get the fiber from the room where its at to the CRS
i would have to move the CRS
[14:51]
plettI don't get on with the CRS devices. I've tried to use them as switches and the vlan config is incomprehensible
I've got dozens of CCR boxes, they're great. And many dozens of virtual mikrotiks. It's just the switches I don't get
[14:52]
nathanihttps://www.youtube.com/watch?v=AgXHc0xCccw [14:54]
BryceBotYouTube video: "99 Problems but a switch aint one - cisco parody" by Kenny hicks [14:54]
staticsafeplett: yeah, RouterOS VLAN configuration is terrible to grok [14:55]
plettstaticsafe: It's fine on the CCRs. I make heavy uses of vlans and bridges on them [14:57]
staticsafeplett: im on of those people who buy a managed switch and use it like a dumb one
so I just need to switch and NAT atm
flat L2, no VLANs
[14:58]
plettI almost always need vlans when I'm using a switch
The most common use-case is a trunk port from a router to a switch containing 4 or 5 vlans, and the switch breaks them out onto different ports
And there's frequently special devices which need to be on multiple vlans
[15:01]
***Lucifer333 has quit IRC (Read error: Connection timed out) [15:02]
plettAnd some of the examples in http://wiki.mikrotik.com/wiki/Manual:CRS_examples#VLAN are just WTF [15:03]
nathanistaticsafe: ##mikrotik suggests you will get max 250 Mbps with your Mikrotik device
" mducharme | you might be able to offset that drop by using something like fasttrack"
[15:05]
plettMikrotik's routers are a friendly UI on top of linux networking functionality. So if you understand things like iptables and brctl then they're awesome. The problem is that they've done the same with the switches - but you need to understand the underlying switch chip instruction set to make any sense of them [15:06]
***Lucifer333 has joined #arpnetworks [15:11]
staticsafenathani: http://www.speedtest.net/result/5925053353 with fasttrack enabled [15:16]
nathaniand you are on gigabit profile? [15:18]
staticsafenathani: yeah
the installer verified that before we left
[15:18]
nathaniyou are getting your upload so theres that [15:18]
staticsafehe* [15:18]
nathaniI didnt test mine with Fasttrack
but wouldnt go over 250
how much more if you bypass the mikrotik?
[15:19]
staticsafenathani: http://www.speedtest.net/result/5924949073
my full speed, depending on the speedtest server
[15:20]
nathaniI dont think these speed test sites do justice to gigabit links
http://www.speedtest.net/result/5925070329
[15:24]
staticsafethey don't yeah
probably should do a iperf test with a localish server
[15:24]
nathanidownload a large linux ISO torrent
it will likely use most of your pipe
[15:25]
.......... (idle for 49mn)
***perlgod has quit IRC (Quit: bye)
perlgod has joined #arpnetworks
[16:14]
................ (idle for 1h18mn)
mkb_ has joined #arpnetworks
mkb has quit IRC (Ping timeout: 264 seconds)
mkb_ is now known as mkb
[17:33]
.... (idle for 16mn)
Lucifer333 has quit IRC (Quit: Leaving) [17:54]
up_the_irons630 Mbps down, holy shit, nice [18:05]
...... (idle for 25mn)
nathanitoo bad it doesnt come with a static IP [18:30]
up_the_ironsi'd buy bandwidth from you if it did
lol
[18:40]
......... (idle for 42mn)
nathanidid I mention its unmetered? [19:22]
mercutioit's probably banned for commercial use [19:27]
nathaniyea they say no servers etc [19:27]
mercutiolots of speedtest servers have 10 gig links now [19:27]
nathaniany public iperf ones? [19:28]
mercutioi dunno about iperf
i mean speedtest.net ones
[19:28]
nathaniiperf.he.net
lol
[19:29]
mercutiolast i knew speedtest doesn't support > gbe clients though [19:29]

↑back Search ←Prev date Next date→ Show only urls(Click on time to select a line by its url)